Kitchen area Cabinet Installation – Step-By-Step Guidelines on How to Set up Kitchen area Cabinets Your self

Now that you have your new kitchen area cupboards, you are all set to go on to the following large action…..Putting in your kitchen area cupboards. Whilst the genuine installation of the Kitchen Cupboards isn’tall that challenging, the vital very first stage is measuring and marking out where the cabinets will go. By putting format markings on the walls and flooring, it will not only aid you with kitchen area cabinet placement and stud locations, but it will also aid you find the place changes and shims will be required. Ahead of we get started there are a pair of products that you will need for the undertaking:


Stage or Laser Degree


Tape Measure

Stud Finder


one” x three” Piece of lumber (6′-8′ in duration) or an Inverted U-formed frame (see notes under)


Screws (lengthy adequate to go 1 1/2 into the studs)

Utility knife or chisel

Marking Compass

An additional set of fingers (you might have to bribe one of your pals)

As I mentioned earlier mentioned, you have the choice of using a piece of 1′ x 3′ lumber for the installation or building a frame to assistance the cupboards (I have integrated a picture of a sample body under). This can be manufactured out of 2′ x 4’s and need to be tall sufficient to assistance the bottom of your wall cabinets. If you plan on setting up far more than 1 kitchen, then I would suggest the frame, but a piece of lumber will do just good if this is a a single time function. In possibly case, you will need to have an additional set of arms to support with the set up.

In this circumstance we bought (RTA) Completely ready-To-Assemble Kitchen Cupboards from RTA Kitchen & Bathroom Cabinet Retailer. Now the kitchen area cupboards are assembled, we are prepared to start off marking out our format traces. Some folks start off with the foundation cabinets, but we are going to begin with the wall cupboards first. There is no appropriate or mistaken way to begin, I just prefer to begin with the higher cupboards first.

1. Use a amount and a pencil to attract a parallel line throughout the wall about 3 inches up from the flooring. Evaluate down from this line, to the ground, and find the floors high point (if it has 1), and mark a line at that level. From that substantial stage, Evaluate up 34 one/2 inches and attract a level line throughout the wall to designate the prime of the base cabinets.

2. Now that you have the leading of the base cupboards marked, measure up an additional 19 1/2 inches and a amount line throughout the wall to point out the base of the wall cupboards. Lightly mark every single cabinets’ proportions and placement on the wall to make positive that your unique format is correct.

three. Use a stud finder to identify the wall studs. Use a pencil to mark the stud locations at least six inches over and below the line for the bottom of the wall cabinets. Attract straight vertical strains in between the leading and base marks to point out the heart of the studs.

4. If Trinity Home Center decided to go with the piece of 1′ x 3′ lumber, now is the place you will use (if you made the decision to go with the U-shaped body, it will occur into enjoy following all your traces are laid out). Screw a momentary 1′ x 3′ assistance rail to the wall, aligning the prime edge of the rail with the line for the base edge of the wall cupboards. Connect it by driving 3 or 4 two inch screws by way of the rail into the wall studs.

5. Now that we have all the lines marked, it is time to start installing your kitchen area cabinets. We are heading to start off with the corner cupboard (right here is where your helper’s added set of fingers will be necessary). Place the corner cabinet on to the short term help rail and have your helper maintain the corner cabinet in spot. Drill pilot holes through the strong cabinet again or its help rail and into the wall studs. Screw the cabinet into the wall using two screws that are lengthy sufficient to penetrate the studs by at least 1 one/two inches. Verify the leading of the cupboard for stage and the entrance of the cabinet for plumb. If you have to right the placement, just back the screws out a little bit and prime shims behind the cupboard at the stud spots. If it is plumb and stage, drive the screws all the way in and add numerous a lot more into every stud to make sure that the cupboard is secured tightly to the wall.

6. Now we are heading to go on to the cupboards on both aspect of the corner cupboard. As you install every a single, use the clamps to protected every cupboard to the neighboring cupboard and then check out it for plumb with your level. On faceframe cupboards, it is a excellent thought to drill two one/eight inch pilot holes through the sides of the faceframe and use screws. In this circumstance, with frameless, all set-to-assemble kitchen area cabinets we are likely to screw by way of the plywood sides and use shims in among the cabinets to make sure a limited suit and make sure that the cabinet faces are plumb.

seven. After all the wall cupboards are in spot, put in the corner or conclude base circumstance cabinet. Use shims exactly where needed to stage the cupboard and increase it up to the line which indicates the higher position of the floor. Be confident it is degree from entrance to again and from aspect to facet, then screw it to the wall studs. If you do not have a diagonal corner cupboard or blind foundation cupboard in the corner, drive the adjoining cabinet into spot and clamp the two units collectively. Include a filler strip if required to permit the doors and drawers sufficient clearance to open and shut properly. If essential, faucet shims below the cupboard and powering it to modify for plumb and amount.

8. Generate screws via the cabinet again (and shims) into the wall studs. Trim any excess content from the shims with a sharp chisel or knife. Continue to add adjoining cabinets in this way, signing up for them the very same way you connected the wall cabinets in step 6.

nine. If your cabinets end up butting from another wall, you might require a filler strip to make up the previous number of inches. If you have custom cupboards, they ought to have been developed to fill this hole, but if you are using stock or RTA Kitchen Cabinets the filler strip may possibly be required. If you do require to use a filler strip, depart the final cupboard detached from the other cabinets. Clamp a straightedge to the confront of the nearest set up unit, extending much enough for you to place alignment marks on the end wall. Allow a 3/four” offset behind these marks (for the thickness of the filler piece) and fasten a cleat to the wall. Then install and fasten the very last cabinet and evaluate the hole between its experience frame and the wall.

If the wall is flat, just rip the filler board to the essential width and fasten it in spot. If the wall is irregular, you are going to have to scribe-match the filler board. Start by placing a marking compass to the width of the hole, then area a strip of one”-broad masking tape alongside the filler board in the spot the place it wants to be trimmed. Clamp the board to the stop cabinet’s encounter frame, then trace the wall contour with the compass. Remove the board and minimize together the scribe line with a jig saw, then reinstall it to verify the fit. When it’s appropriate, drive screws by means of the adjacent experience frame into the edge of the filler board. Screw or nail the other aspect to the cleat.

At this position, your kitchen cabinet installation is full. If you bought matching crown molding or any other information, these need to be effortlessly set up now. Relying on regardless of whether you experienced to use shims beneath the foundation cupboards, you could have to set up some trim items by the toe kicks to go over up the shims or any gaps at the base of the kitchen area cabinets.

I hope this helps make your kitchen area cupboard installation as sleek as attainable. If you need to have any aid with cupboard variety, kitchen layout tips, or concepts for cabinet styles, examine out RTA Kitchen & Rest room Cupboard Store

Leave a Reply

Your email address will not be published. Required fields are marked *